You must log in or register to comment.
This isn’t proper lock out, tag out procedure. They forgot the lock part and only have a tag.
this is NOT tag out lock out approved holy fuck
Yeah I came here to say that this is a fucking terrifying “LOTO” (and I’m using the term very loosely here) procedure that most likely will eventually kill someone
absolutely. I’d almost want to disassemble something like this before cleaning it properly.
That or have a very explicit physical lock out mechanism if it’s something like a stamping press.
I actually knew a guy who died this way at a Caterpillar factory near Peoria, IL. Machine wasn’t properly tagged out/locked out.
RIP Troy Bryner
Update:
Per OSHA Report:
Investigation Nr: 200272276 Event: 04/17/2011 Employee Is Killed When Struck By Closing Lid At approximately 11:00 a.m. on April 17, 2011, Employee #1 performing maintenance on a Dunker quench hardening machine that included the repair of a hydraulic leak. He was working in an area that measured approximately 2 feet wide by 3 foot long by 4 feet deep. Employee #1 locked out the machine’s control panel and made the necessary repairs. After completing the repair work, Employee #1 instructed a coworker to remove the locks in order to verify that there were no leaks. While in the machine, Employee #1 attempted to lower the machines hydraulic cylinder by depressing the “lower press elevator” button. Instead, he depressed the “lower press lid” button. This caused the machines lid to close on Employee #1’s head, killing him. The accident investigation reported that the coworker was working to secure the “lower press lid” cover by chaining it open; however, was not able to secure it in time due to the untimely depression of its activation button.
So, not exactly a failure to lock/out, but certainly an example of how important it is to take those types of procedures seriously. Always, good to know what actually happened.
What a terrible way to go
34 too :(
Should we lock & tag out the circuit?
Nah, this shitty sign should keep us safe.
Engineering the future at Boeing!
Yes but that cost money. And the company stock buy backs and executive bonuses needs to happen.
Y’all got any of them lockout/tagouts?
Lockouts SMH. Back in my day, we just died. And we were happy to work on energized systems for a bee (which was the style at the time).
You got paid? We used to have to pay for the privilege of being crushed to death at work.
We have lockout/tagout at home
Lockout/tagout at home
why aren’t they doing lockout tagout?
Because they’re doing note out hope out. Obviously.
Can they not just, unplug it, and put tape over the power point.
Same thing I thought, unless there isn’t a place for a lock.
There is always a way to disable a machine. The button has power. At the very least, the power to that button should be locked out. If it has to happen at the breaker, so be it.
Today on hoodroolic press channel, ve haff an intern, a new intern who’s cleaning the press, and he looks prooty dangerous, so ve must deel vif it.
When preparing/working on a machine, TURN IT OFF. IT IS LITERALLY THE FIRST STEP WHEN REPAIR ANY PIECE OF EQUIPMENT YOU STUPID PIECE OF SHIT.
Sometimes this isn’t possible if the machine needs to stay up to temp, like with plastic injection molders. In those cases, the operation can usually be stopped by a padlock placed somewhere on the controls. There’s usually training about it for everyone involved to make sure they know what’s up.
And if there’re multiple people involved each one should have their own pad lock placed on the controls.
Lock out, tag out
That too, but Jesus, how dense do you have to be to not even turn the machine off?
Also ZIPTIE it off
And unplug it. And lock it out so some dumbass can’t plug it back in and turn it on.
Is there a charge for “attempted negligent homicide” or something? You did something so catastrophically stupid that was all but guaranteed to kill someone except you got lucky, but you still should end up getting censured so you don’t roll the dice on someone’s life again
Reminds me of an story I heard once. Guy working on a job locks and tags out a circuit so he can work on it. Guy goes up on a ladder to do the work.
Coworker comes along and sees circuit left locked; he decides he needs to activate the circuit. Coworker uses bolt cutters to remove the lock and flips on the circuit.
Guy on ladder gets literally knocked off the ladder, falls 10-20 feet onto grass. Guy is rushed to the ER.
Boss investigates, gives coworker two options: either he can quit immediately, or he can keep working and personally explain himself to guy in a month when he gets out of the hospital.
I remember reading something similar, with someone responding that they were always two people for these tasks. One doing the job and one guarding the circuit, making sure this does not happen.
This is why you need 2 people to reactivate the circuit, one with the boltcutters, the other to fight the guard.
Where I live, for that kind of incident the employer would be obligated (as in, $50k worth of fines and likely criminal charges if you don’t) to report it to an independent investigator to determine who was at fault; the person cut the lock would be liable for a fine, and the employer would have to prove that they adequately trained the employee before allowing them to work in a high risk area, or the health and safety officer and company directors could be found criminally liable
In my area, there’s a decent chance the guy with the bolt cutters could be criminally liable, if he was adequately trained. That could easily be negligent homicide.
You do not cut locks. If your boss asks you to cut a lock, report them so they get immediately fired. We don’t fuck around with LOTO.
I worked briefly at a store where the Store Director was clearly still traumatized about an employee death years prior. Didn’t press for details, but it was preventable and they were hyper-vigilant about safety precautions.
The world would be better without Captain Bolt Cutter and their kind spreading misery with their weaponized stupidity.
I think this is what you’re looking for.
Can you perhaps relate that information in a format that doesn’t involve me watching a video?
Respectfully, you are not required to get any information in a format that you don’t want it. But also I don’t have to provide anything in a way that would otherwise inconvenience me for a random stranger who doesn’t even have the decency to say please.
If you don’t have less than 2 minutes for a video then don’t take the time to watch it.
I didn’t say you were required to, jeez. I just asked.
I don’t click on video links because they are almost always a giant waste of time.
Looks like it’s a meme video (clip from the Simpsons) so yes, just a waste of time.
I’m in public and don’t have headphones. I’m not clicking a video and bothering everyone around me.
Was hat die Reinigungskraft im Kraftwerk gesagt?
“Schalt jetzt bloß nicht die Turbiiiiiiiiiiiiiiiiiiiiieeeeeeeeeeeeeeeeeeeeeee…”
When your life is protected by, and depends on a little scribbled piece of paper…
4th February that’s an old note, better remove it and press.
Had the same thought. The American date format must be the least intuitive, but as a nerd that likes to order files and folders YYYY/MM/DD is just a win.
You meant YYYY-MM-DD
If we’re having a fight over who can be the most padentic, I’d argue that’s a format issue, rather than order ;)
But then again, I’m a few pints deep now and may just be talking out me arse.
YYYYMMDD
Someone databases
Not really, that’s just the standard of ISO 8601. In the past I used slashes as well until someone mentioned standard is to use dashes and not slashes. Dashes also seem to have better readability.
Dashes also work in filenames.
That’s just for weak machines who need to be constantly reminded what year it is.
Y’all need tag out clasps
You lock it with 6 pad locks?
Just one padlock is enough, but you can use up to 6.
You need all the locks removed before it’ll open, so you don’t need to count on someone to carefully count everyone back in. You just make sure that each person uses their own lock
I think it’s so you can create “and” conditions for unlocking. IE: If you’ve got two locks, each with their own key, both person 1 AND person 2 need to unlock it. So you can have multiple people and/or multiple crews working on the machine across different aspects. Maybe one crew is doing electric, the other some kind of plumbing, and they’re working at different times. When one crew finishes their work, they can release their lockout without making it unsafe for the other crew.
Exactly this. Everyone working on that machine slaps their lock on it, and every last lock needs to be removed before the tag can come off. The welders might finish in half a day, but the electrical or water or hydraulic guys might need a whole weekend to get done, so this makes sure someone doesn’t say “oh the lock is gone” and make mincemeat out of some dude’s head.
Thought so. I work around this stuff but my end of it usually low voltage/low pressure/ low risk. We should observe it more but usually we just have someone that LOTOs anything going to us.
But yeah, and for anyone else, repairs can wind up being more complicated than anticipated, parts arrive late, etc. It’s not uncommon for these to be in place for weeks sometimes when say, electrical starts something, but then plumbing needs to finish whatever before the pump motor hookup can be complete. Before you know it it’s 2 weeks later, electrical had a bunch of other jobs. The LOTO makes sure they come and inspect before unlocking rather than go “yeahhhh I’m pretty sure we left that ready to turn on, go for it” plus making sure no other work got screwed up (like a wire conduit getting drilled into by plumbing).
To be sure, handing off the keys does happen, but if and when it happens there’s the weight of “by handing this off you’re personally taking responsibility”.
You’re entitled, usually required, to add your personal lock onto this when you start working on a locked out job, that way you can be confident they’ll come looking for the last guy to lock off the job before they can get running again, it may save your fingers/arm/life or job. Usually there’s a permit involved and you should know the conditions of the permit, or have your own permit to join a job.
You know, we’re not required to do that but because of you I just ordered some locks and labels for the field kit (edit: as well as breaker locks).
Our stuff is always temp (8-12mo) and on a dedicated line. The sites we’re on always involve coordinating with the clients appropriate people and specifically stating we’re not trained in this to their standards (which is why I know some of this stuff but not to the letter), but an extra layer is always a good idea. No harm ever came from an extra lock that couldn’t be fixed.
Thanks.
edit: for the record it’s not like we’re negligent, everything in our system is designed to fail-safe, and we compartmentalize power delivery, but still, no harm in a few extra items in the kit.
that looks like a flogger ngl
I flogged ur mum
I saw
Lock Out/ Tag Out what? Just post a handmade sign, dude
Well, the button says “pull to start” and the sign says “do not push” so we’re good to start it, right?
they cancel one another out and it’s dealer’s choice
